Troubleshooting

Find your problem below. If it is not listed, see Report a problem.

Building your own Morse Scout? See Build troubleshooting.

Keys and sending

My key makes no sound and nothing is decoded.

  1. Open Settings → Keyer, choose the Key Input your key is plugged into, and check Key Type is not Not Connected. New devices start with every input set to Not Connected.
  2. Check the plug is fully inserted in the correct jack.
  3. Check the volume knob and Settings → Device → Volume.

One of my keys works but another does not.

  • Each input has its own settings. Set up the second input in Settings → Keyer.
  • If a key was held down or shorted when Morse Scout started, release it. The input starts working once it has been released.

My paddle sends dits and dahs the wrong way round.

Change Contact Order for that input in Settings → Keyer.

The keyer sends an extra dit or dah when I release the paddles.

You may be using Iambic-B. Try Iambic-A. See Keyer and key inputs.

My bug produces extra short dits.

Turn on Bug Tweaks and increase Leading Dit Debounce or Trailing Dit Debounce a few milliseconds at a time.

Send Practice shows many red question marks.

The decoder could not recognise your patterns. Set the speed closer to the speed you are sending, and check the spacing inside characters.

Timing Check asks me to configure Keyer settings.

Timing Check needs an input set to Straight Key or Bug. Paddles are not used.

Sound

I hear nothing at all.

  1. Turn the volume knob up.
  2. Check Settings → Device → Volume is not 0.
  3. Check Settings → Sidetone → Output Volume is not 0%.

Speech is missing in Receive Words or Receive Book.

  • Check Say After, Say Before or Talk is on.
  • The voice may take a few seconds to load the first time.
  • If speech never works, the activity continues in Morse only. The voice may need reinstalling with the recovery installer; contact us first.

Practice noise is still playing.

Noise only plays in Send Practice and stops when you leave it. Select the Mute button in the advanced panel to silence it while staying in Send Practice.

Screen and controls

The screen is dark.

  • Morse Scout may be asleep. Press the sleep/wake button.
  • Check Settings → Device → Brightness.
  • Charge the battery.

The rotary encoder does nothing on some screens.

The encoder is not used on the Receive Book and Wi-Fi screens. Use the touchscreen there.

Settings

My settings were not kept.

Select ✓ (Save) before leaving a settings screen. ✗ (Cancel) discards changes.

The volume returns to an old value after restarting.

The volume knob changes the volume for the current session. Open Settings → Device and select ✓ to save it.

Clock

The clock is not shown.

The clock appears only when the time is known. Connect to Wi-Fi with Time Synchronization set to Automatic, or set the time yourself in Manual mode. See Time.

The time is wrong by whole hours.

Check Settings → Time → Time Zone.

Wi-Fi

No networks are found.

  • Morse Scout supports 2.4 GHz Wi-Fi only. Make sure your router offers a 2.4 GHz network.
  • Select Rescan, and move closer to the router.

“Wrong password”.

Re-enter the password. Passwords are case-sensitive.

“Module not responding” or “Wi-Fi link lost”.

Restart Morse Scout. If this keeps happening after a firmware update, the Wi-Fi module’s firmware may need updating; see the release notes or contact us.

microSD card and files

My list or book does not appear.

  • Check the card is FAT32 or exFAT and fully inserted. FAT12 and FAT16 are also supported, but are uncommon on current cards.
  • If the card cannot be mounted, back it up and reformat it with the official SD Memory Card Formatter. Morse Scout does not format cards itself.
  • Lists must be in a folder called lists and end in .txt. See Word and phrase lists.
  • Books must end in .txt. See Books.
  • Only up to 96 items are listed in a folder.

Receive Book shows an error.

See the message table on Receive Book.

Firmware updates

See Update firmware, section “If the update will not start”.